Whatman GD/X Nylon Syringe Filters, 0.2 µm, 25 mm, 150/Pk - 6871-2502
Whatman ties GD/X prefiltration performance to one closely held fiber-grade standard applied at every production run, keeping results repeatable from one manufacturing lot to the next. At the sub-micron pore rating, a syringe filter delivers sterilizing-grade retention at the point of use. Nylon withstands elevated differential pressures while drawing aqueous samples through without pre-wetting and tolerates alcohols and aliphatic and aromatic solvents. The polypropylene housing maintains its geometry through sample runs up to 121°C while routing flow to minimize backpressure in service and preserves sample chemistry across the flow path. When sample preparation calls for a sterile filtrate at the point of injection, sterilizing-grade absolute retention delivers it directly, protecting the analytical method from microbial interference.
Prefiltration
- Glass microfiber depth media loads particulate across its full thickness
- Upstream glass microfiber prefilter layer captures coarse particulate ahead of the membrane
- High dirt-holding capacity extends usable throughput by delaying membrane clogging
- Nominal glass microfiber depth layer sustains flow through high-solids, particle-laden samples
Membrane Characteristics
- Non-sterile format suits HPLC and GC sample clarification
- Tortuous, reticulated pore structure yields more usable filtration area than capillary-pore membranes
- Alkaline-resistant across a broad range of aqueous buffers
- Common ketone solvents, including acetone, methyl ethyl ketone, and methyl isobutyl ketone, cause no attack
- Saturation moisture uptake reaches up to 8% by resin weight
Housing Characteristics
- Polypropylene density near 0.90 g/cm3 keeps housing weight low relative to denser engineering plastics
- Rigid polypropylene body maintains its geometry through routine filtration pressure
- Minimal extractable release from the housing supports sensitive analytical work downstream
- Inert polyolefin wall contributes minimal sample adsorption to the filtrate
Unfiltered particulates shift your retention times and peak shapes from run to run. Upstream sample clarification keeps your separations clean and reproducible from sample preparation through final injection. Request a quote on Whatman filtration products from the Tisch Scientific team.
Sterilization Guidance
Standard autoclave cycles at 121°C for 30 minutes prepare the device for sterile workflows.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 2.9 bar (42 psi)
- Burst Pressure (psi)
- 75psi
- Connection Type
- Luer-Lok/ Luer Slip
- Construction
- Polypropylene
- Diameter
- 25mm
- Filtration Area
- 4.6cm²
- Flow Rate
- 46
- Holdup Volume
- 1.4ml
- Material
- Nylon
- Maximum Operating Pressure
- 75psi
- Maximum Operating Temperature (°C)
- 121°C
- Pack Count
- 150
- Pore Size (µm)
- 0.2
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- Glass Microfiber (GMF)
- Sterility
- Nonsterile
- Sterilization
- Autoclavable 121°C
- Volume Throughput (ml)
- Up to 100ml
- Wettability
- Hydrophilic
- Ink and Dye Filtration - Filters aqueous and solvent-based inks and dyes, removing pigment agglomerates ahead of color strength analysis.
- Beverage QC Clarification - Clarifies wine, beer, and juice samples ahead of analytical and microbiological testing in quality control labs.
- Environmental Extract Prep - Clarifies water and soil extracts ahead of trace metals or pesticide-residue analysis for accurate results.
- UHPLC Sample Prep - Removes sub-micron debris from aqueous samples before injection, protecting narrow-bore UHPLC columns from accelerated wear.
- Fermentation Monitoring - Clarifies samples from microbial fermentation for rapid analyte measurement of glucose, ethanol, and metabolite levels.
- Biofuel Particulate Testing - Removes particulate debris from biodiesel and fuel samples ahead of chromatographic QC analysis in fuel testing labs.