Whatman GD/X Nylon Syringe Filters, 5 µm, 25 mm, 150/Pk - 6871-2550
Whatman places a fibrous glass mat before the final membrane in every GD/X device, clearing a turbid sample in one pass through the same housing. Many syringe filters ship with lot-specific quality documentation, giving analysts documented traceability beyond what an ad hoc bulk filtration setup typically provides. Naturally hydrophilic nylon accepts water-based samples without surfactant preconditioning and holds consistent retention across mixed-phase samples. The polypropylene housing maintains its geometry through sample runs up to 121°C while resisting degradation from routine sample matrices and leaves no seam for sample to bypass the membrane. Where analytical results depend on clean samples, the preparation step stays consistent from sample to sample through a pre-tested syringe filter.
Prefiltration
- Glass microfiber prefilter shields the downstream membrane from bulk particulate
- Upstream glass microfiber prefilter layer captures coarse particulate ahead of the membrane
- High dirt-holding capacity extends usable throughput by delaying membrane clogging
- Nominal glass microfiber depth layer sustains flow through high-solids, particle-laden samples
Membrane Characteristics
- Hydrophilic surface takes up aqueous samples with no pre-wetting
- Non-sterile format suits HPLC and GC sample clarification
- Alkaline-resistant across a broad range of aqueous buffers
- DMSO compatibility extends across sample-preparation chemistries
- Synthetic polyamide backbone resists microbial and enzymatic degradation unlike cellulose membranes
Housing Characteristics
- Medical-grade polypropylene with broad chemical compatibility
- Low moisture absorption keeps the housing dimensionally stable through humid storage and shipping
- Withstands standard 121°C steam autoclave cycles without softening or structural distortion
- Optimized internal geometry minimizes backpressure in service
A particulate-laden aqueous sample makes the rest of your preparation unpredictable. General-purpose aqueous filtration supports the sample types you handle every day from reagent and buffer preparation through routine sample clarification. Request Whatman's quality documentation to support your filtration step meeting a recognized laboratory-science standard.
Sterilization Guidance
Customer autoclave compatibility at 121°C accommodates in-lab sterilization timing.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Burst Pressure (psi)
- 75psi
- Connection Type
- Luer-Lok/ Luer Slip
- Construction
- Polypropylene
- Diameter
- 25mm
- Filtration Area
- 4.6cm²
- Holdup Volume
- 1.4ml
- Material
- Nylon
- Maximum Operating Pressure
- 75psi
- Maximum Operating Temperature (°C)
- 121°C
- Pack Count
- 150
- Pore Size (µm)
- 5
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- Glass Microfiber (GMF)
- Sterility
- Nonsterile
- Sterilization
- Autoclavable 121°C
- Volume Throughput (ml)
- Up to 100ml
- Wettability
- Hydrophilic
- Tissue Homogenate Prep - Pairs a glass-fiber prefilter with a nylon final membrane to clarify particulate-heavy tissue homogenates for analysis.
- IC Column Protection - Clarifies aqueous samples ahead of anion and cation analysis, guarding ion-exchange columns against particulate fouling.
- Cannabis Potency Testing - Clarifies cannabinoid extracts in ethanol or hydrocarbon solvents ahead of HPLC potency and pesticide-residue analysis.
- GC Sample Prep - Clarifies aqueous and organic extracts ahead of gas chromatography injection, protecting inlets from particulate fouling.
- HPLC Pump Protection - Filters reservoir solvent to prevent particulates from abrading pump check valves and seals over time.
- Dissolution Testing - Supports accurate drug release profiles by clarifying dissolution samples ahead of HPLC quantitation in QC labs.