Whatman GD/X PTFE Syringe Filters, 0.2 µm, 13 mm, 150/Pk - 6875-1302
Whatman pairs a borosilicate fiber depth layer with the finishing membrane inside every GD/X unit, a construction meant to process loads heavy enough to clog a conventional one-stage filter. A syringe filter with a hydrophobic vent-rated membrane keeps gas and vent lines free of microbial ingress. Hydrophobic PTFE blocks aqueous ingress in vent and gas applications while staying chemically inert against solvents, acids, and alkalis in service and handles concentrated acids and bases. The polypropylene housing holds its seal true run after run while holding its form through high-temperature sample preparation conditions and stays inert across common laboratory solvents. No separate sterilization cycle is needed when the gas path already runs through a validated sterile-grade membrane.
Prefiltration
- Glass microfiber prefilter shields the downstream membrane from bulk particulate
- Nominal glass microfiber depth layer sustains flow through high-solids, particle-laden samples
- Upstream glass microfiber prefilter layer captures coarse particulate ahead of the membrane
- Glass microfiber depth media loads particulate across its full thickness
Membrane Characteristics
- High membrane porosity, 70 to 80 percent void volume, delivers high flow at low pressure
- Surface energy near 18.5 dynes per centimeter repels oils and nonpolar liquids
- Water contact angle near 120 degrees marks strong hydrophobicity
- Low non-specific protein binding preserves recovery of biomolecules and therapeutic proteins during filtration
- Fully fluorinated carbon backbone resists ultraviolet and ozone degradation
Housing Characteristics
- Minimal extractable release from the housing supports sensitive analytical work downstream
- Standardized luer connection geometry provides secure engagement with standard syringe tips
- Housing tolerates elevated-temperature aqueous and solvent sample filtration up to about 80°C without softening
- Burst pressure rating provides a wide safety margin above the rated maximum operating pressure
Particulates left in your organic solvents and reagents carry downstream into the step that depends on a clean feed. Reliable solvent prefiltration keeps a stray particulate from carrying into your downstream work from reaction mixtures and crude extracts through further processing. Request available pack sizes and lead times across this filtration line's membrane options from the Tisch Scientific team.
Sterilization Guidance
Customer autoclave compatibility at 121°C accommodates in-lab sterilization timing.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 1.0 bar (15 psi) [IPA]
- Burst Pressure (psi)
- 75psi
- Connection Type
- Luer-Lok/ Luer Slip
- Construction
- Polypropylene
- Diameter
- 13mm
- Filtration Area
- 1.3cm²
- Holdup Volume
- 0.5ml
- Material
- Polytetrafluoroethylene (PTFE)
- Maximum Operating Pressure
- 75psi
- Maximum Operating Temperature (°C)
- 121°C
- Pack Count
- 150
- Pore Size (µm)
- 0.2
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- Glass Microfiber (GMF)
- Sterility
- Nonsterile
- Sterilization
- Autoclavable 121°C
- Volume Throughput (ml)
- Up to 10ml
- Wettability
- Hydrophobic
- Air Monitoring - Ensures precise capture of airborne particulates for environmental analysis in demanding atmospheric monitoring conditions.
- Extractables Testing - Clarifies packaging material organic solvent extracts ahead of LC-MS analysis, keeping background low for leachable detection.
- Dissolution Testing - Stops the dissolution reaction and clarifies samples, with low API binding for accurate potency quantitation.
- Aggressive Solvents - Clarifies chlorinated hydrocarbons and aromatics without membrane degradation, delivering pure filtrate quality consistently.
- Toxicology Screening - Clarifies protein-precipitated serum, plasma, and urine extracts ahead of LC-MS or GC-MS drug screening analysis.
- Photoresist Filtration - Clarifies photoresist solutions in organic casting solvent ahead of spin-coating, reducing particulate defect risk.