Whatman GD/X Cellulose Acetate (CA) Syringe Filters, 0.45 µm, 25 mm, 150/Pk - 6880-2504
Whatman places a fibrous glass mat before the final membrane in every GD/X device, clearing a turbid sample in one pass through the same housing. A syringe filter's small hold-up volume limits sample loss, a meaningful difference when working with a limited or precious sample. Cellulose acetate's hydroxyl chemistry wets on contact, no coating needed while keeping filtrate clean ahead of analysis and suits aqueous solutions, buffers, and alcohols. Polypropylene construction maintains a low-dead-volume internal flow path and holds its seal true run after run. For routine sample preparation across many methods, each analytical run starts with a consistent, particle-free sample without added hardware or a cleaning step.
Prefiltration
- Glass microfiber depth media loads particulate across its full thickness
- Glass microfiber prefilter shields the downstream membrane from bulk particulate
- High dirt-holding capacity extends usable throughput by delaying membrane clogging
- Nominal glass microfiber depth layer sustains flow through high-solids, particle-laden samples
Membrane Characteristics
- Naturally hydrophilic surface wets readily with aqueous samples
- Smooth membrane face with even pore distribution across the active filtration area
- BSA adsorption near 3.8 micrograms per square centimeter across the membrane
- Cellulose ester backbone stable across aqueous pH range of 4 to 8
- Low extractable contribution keeps filtrate chemistry clean
Housing Characteristics
- Thermal-bonded construction keeps adhesives out of the fluid path
- Polypropylene density near 0.90 g/cm3 keeps housing weight low relative to denser engineering plastics
- Standardized luer connection geometry provides secure engagement with standard syringe tips
- PP housing rated to 121°C holds its geometry through high-temperature sample preparation and processing
Particulates in your buffers, reagents, and aqueous samples slow your preparation and throw off its consistency. General-purpose aqueous filtration supports the sample types you handle every day so you can standardize one filter across most aqueous methods. Request Whatman's quality documentation to support your filtration step meeting a recognized laboratory-science standard.
Sterilization Guidance
The housing supports customer autoclave sterilization at 121°C for 30 minutes.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 2.0 bar (29 psi)
- Burst Pressure (psi)
- 75psi
- Connection Type
- Luer-Lok/ Luer Slip
- Construction
- Polypropylene
- Diameter
- 25mm
- Filtration Area
- 4.6cm²
- Flow Rate
- 29
- Holdup Volume
- 1.4ml
- Material
- Cellulose Acetate
- Maximum Operating Pressure
- 75psi
- Maximum Operating Temperature (°C)
- 121°C
- Pack Count
- 150
- Pore Size (µm)
- 0.45
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- Glass Microfiber (GMF)
- Sterility
- Nonsterile
- Sterilization
- Autoclavable 121°C
- Volume Throughput (ml)
- Up to 100ml
- Wettability
- Hydrophilic
- Urinalysis Prep - CA clarifies urine samples by removing particulates ahead of automated urinalysis without altering biochemical composition.
- DNA Extraction Prep - CA's low-binding surface passes aqueous DNA extracts cleanly ahead of PCR, gel electrophoresis, and sequencing preparation.
- Microbial Limit Testing - CA membrane retains microorganisms from pharmaceutical solutions for USP microbial limits testing and bioburden assessment.
- Fermentation Broth Prep - CA filters clarify fermentation broth samples, removing biomass ahead of glucose, ethanol, and metabolite measurement.
- Alcohol Compatibility - Handles low molecular weight alcohols reliably, supporting specialized chemical clarification tasks in the laboratory.
- Stability Testing Prep - Hydrophilic CA membrane clarifies stability samples without analyte loss, supporting accurate potency tracking over time.