Whatman GD/XP Polyethersulfone (PES) Syringe Filters, 0.45 µm, 25 mm, 150/Pk - 6995-2504
GD/XP swaps the glass fiber prefilter for layered polypropylene inside the same compact housing, keeping ion backgrounds low for samples headed to ICP-OES or ICP-MS. Syringe filters span a wide range of membrane chemistries and pore sizes, so the format can be matched to the sample matrix and solvent system in use. PES's open pore layout leaves proteins less surface to contact and separates particulates precisely at its micron cutoff. The polypropylene housing holds its seal true run after run while preserving sample chemistry across the flow path and routes flow to minimize backpressure in service. Where analytical results depend on clean samples, the preparation step stays consistent from sample to sample through a pre-tested syringe filter.
Prefiltration
- Low pressure drop across the depth layer supports higher-throughput processing
- Nonwoven polypropylene matrix captures coarse particulate through its depth
- Polypropylene prefilter resists acids, bases, and common organic solvents
- High dirt-holding capacity sustains flow through turbid, viscous, particle-laden samples
Membrane Characteristics
- Non-ionic surface avoids charge-driven protein binding of positively and negatively charged membrane types
- Chemical breadth spans alcohols, glycols, and aqueous buffers
- Sulfone backbone's hydrolytic stability tolerates repeated autoclave steam sterilization cycles
- Aromatic sulfone backbone underlies stability across the full pH range
- Ionic extractables from the membrane stay very low
Housing Characteristics
- Withstands standard 121°C steam autoclave cycles without softening or structural distortion
- PP housing rated to 121°C holds its geometry through high-temperature sample preparation and processing
- Stable across the full aqueous pH range in routine sample work
- Polypropylene density near 0.90 g/cm3 keeps housing weight low relative to denser engineering plastics
Particulates in your buffers, reagents, and aqueous samples slow your preparation and throw off its consistency. Consistent aqueous clarification clears particulates without slowing your bench routine the same way every time you run it. Request volume pricing and stock availability on your filtration product selection from the Tisch Scientific team.
Sterilization Guidance
Customer autoclave compatibility at 121°C accommodates in-lab sterilization timing.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 2.3 bar (33 psi)
- Burst Pressure (psi)
- 75psi
- Connection Type
- Luer-Lok/ Luer Slip
- Construction
- Polypropylene
- Diameter
- 25mm
- Filtration Area
- 4.6cm²
- Holdup Volume
- 1.4ml
- Material
- Polyethersulfone (PES)
- Maximum Operating Pressure
- 75psi
- Maximum Operating Temperature (°C)
- 121°C
- Pack Count
- 150
- Pore Size (µm)
- 0.45
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- Polypropylene (10µm + 5µm)
- Sterility
- Nonsterile
- Sterilization
- Autoclavable 121°C
- Volume Throughput (ml)
- Up to 100ml
- Wettability
- Hydrophilic
- Trace Metal Prep - Processes samples ahead of trace metal analysis using a low-extractable prefilter that avoids added background metal ions.
- Life Science Prep - Speeds processing of viscous biological solutions, improving laboratory workflow efficiency during busy sample prep days.
- Pesticide Residue Testing - PES membranes improve polar pesticide recovery in food-safety LC-MS/MS testing versus hydrogen-bonding nylon.
- PFAS Water Testing - PES filters process aqueous samples for EPA Method 1633A PFAS testing without added fluorinated background.
- Urine Drug Screening - Clarifies protein-poor urine samples for dilute-and-shoot LC-MS/MS toxicology testing without adsorbing target drug analytes.
- Organic Carbon Testing - Clarifies water samples ahead of DOC and UV254 analysis while keeping organic carbon adsorption to the membrane minimal.