Tisch Scientific PVDF Syringe Filters, 0.22 µm, 30 mm, 100/Pk - SF15616
Tisch Scientific's representatives greet every caller with patience, whatever brings them to the phone. A syringe filter with a hydrophobic vent-rated membrane keeps gas and vent lines free of microbial ingress. PVDF provides sterilizing-grade retention at the rated sub-micron pore size while resisting HPLC mobile phases, alcohols, and mild hydrocarbons and blocks aqueous ingress in venting applications. The polypropylene housing routes flow to minimize backpressure in service while shedding virtually no extractable material into the sample and presses snugly against the membrane during the pass. A vent or gas line stays free of airborne bacteria once a hydrophobic, sterilizing-grade membrane is in the path.
Membrane Characteristics
- Bacterial challenge testing with Brevundimonas diminuta at 10 million CFU per cm2 confirms sterilizing grade
- Hydrophobic surface chemistry gives PVDF a water contact angle above 100 degrees, blocking wetting
- Fluorinated polymer chemistry resists ozone, UV, and ionizing radiation
- Resistance to hydrolytic degradation exceeds that of nylon membranes
- Absolute pore rating ensures reproducible results between test runs
Housing Characteristics
- Polypropylene housing tolerates dilute aqueous acids, bases, and alcohols used in routine sample prep
- Plasticizer-free polyolefin construction keeps the fluid path clean
- Minimal intrinsic autofluorescence from the polypropylene housing supports background-sensitive fluorescence-based assay work downstream
- Translucent housing wall allows visual confirmation of sample flow during filtration
Particulates left in your organic solvents and reagents carry downstream into the step that depends on a clean feed. Solvent-stream filtration handles the solvents and reagents your methods rely on so your filter holds its integrity through the run. Contact Tisch Scientific for a quote, lead time, or stock-on-hand check on your filtration product selection.
Sterilization Guidance
Customer autoclave compatibility at 121°C accommodates in-lab sterilization timing.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 14.5psi
- Burst Pressure (psi)
- 87psi.
- Connection Type
- Luer-Lok/Luer Slip
- Construction
- Polypropylene (PP)
- Diameter
- 30mm
- Filtration Area
- 4.9cm²
- Flow Rate
- 24.5ml
- Holdup Volume
- 100μL
- Material
- Polyvinylidene Fluoride (PVDF)
- Maximum Operating Pressure
- 87psi
- Maximum Operating Temperature (°C)
- 60°C
- Membrane Thickness (µm)
- 100-130μm
- Pack Count
- 100
- Pore Size (µm)
- 0.22
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- PP
- Sterility
- Nonsterile
- Sterilization
- Autoclave at 121°C for 30min/ gamma 25kGy
- Volume Throughput (ml)
- 110ml
- Weight
- 0.91
- Wettability
- Hydrophobic
- Sterile Tank Venting - Blocks aqueous ingress on storage tanks and carboys, letting sterile air and gas pass through the vent line.
- Compressed Gas Filtration - Passes nitrogen and other inert gases freely while holding back moisture, protecting instruments and gas lines.
- Culture Vessel Filling - Equalizes pressure in sealed culture vessels by venting displaced air, keeping fill and drain lines fully closed.
- Dissolution Testing - Removes undissolved particles from timed USP 711 dissolution aliquots, preventing skewed potency and release results.
- Vial and Tubing Venting - Blocks liquid while venting sealed vials and tubing lines, keeping pressure equalized during fluid transfer steps.
- Organic Solvent Filtration - Wets readily with alcohols and mild hydrocarbons, delivering dependable clarification of organic solvent samples.