Tisch Scientific PVDF Syringe Filters, 0.45 µm, 25 mm, 100/Pk - SF18309
Tisch Scientific vets its filtration partners carefully, favoring those with a consistent record of dependable output. Many syringe filters ship with lot-specific quality documentation, giving analysts documented traceability beyond what an ad hoc bulk filtration setup typically provides. PVDF holds consistent absolute retention at the rated pore size while blocking aqueous ingress in venting applications and holds up to alcohols and mild hydrocarbon solvents. The polypropylene housing holds its seal true run after run and stands firm against aqueous acids, bases, and alcohols during regular handling. Where analytical results depend on clean samples, the preparation step stays consistent from sample to sample through a pre-tested syringe filter.
Prefiltration
- Depth media that capture particulate through their full thickness
- Layered glass fiber and polypropylene depth media
- High dirt-holding capacity for the heaviest particulate loads
- Two-stage construction with the prefilter ahead of the final membrane
Membrane Characteristics
- Cast membrane structure releases no fibers, unlike depth-media prefilters
- Fluorinated polymer chemistry resists ozone, UV, and ionizing radiation
- Organic solvent resistance beats PES or nylon at comparable pore size
- Limiting oxygen index runs high, supporting flame resistance and low smoke
- Ethylene oxide sterilization cycles leave pore integrity and flow performance intact
Housing Characteristics
- Polypropylene housing tolerates dilute aqueous acids, bases, and alcohols used in routine sample prep
- Plasticizer-free polyolefin construction keeps the fluid path clean
- Standardized luer connection geometry provides secure engagement with standard syringe tips
- Withstands standard 121°C steam autoclave cycles without softening or structural distortion
Particulates left in your organic solvents and reagents carry downstream into the step that depends on a clean feed. Reliable solvent prefiltration keeps a stray particulate from carrying into your downstream work from reaction mixtures and crude extracts through further processing. Request a quote on bulk pricing for larger filtration orders from the Tisch Scientific team.
Sterilization Guidance
Standard autoclave cycles at 121°C for 30 minutes prepare the device for sterile workflows.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 5.8psi
- Connection Type
- Luer-Lok/Luer Slip
- Diameter
- 25mm
- Filtration Area
- 4.08cm²
- Flow Rate
- 32ml
- Holdup Volume
- 100μL
- Material
- Polyvinylidene Fluoride (PVDF)
- Maximum Operating Pressure
- 87psi
- Maximum Operating Temperature (°C)
- 60°C
- Membrane Thickness (µm)
- 100-130μm
- Pack Count
- 100
- Pore Size (µm)
- 0.45
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- GF+GF+PP
- Sterility
- Nonsterile
- Sterilization
- Autoclave at 121°C for 30min/ gamma 25kGy
- Volume Throughput (ml)
- 50ml
- Weight
- 0.52
- Wettability
- Hydrophobic
- Organic Solvent Filtration - Wets readily with alcohols and mild hydrocarbons, delivering dependable clarification of organic solvent samples.
- Petroleum Sample Prep - Removes particulates from fuel and lubricant samples ahead of viscosity and quality-control testing.
- Beverage QC - Clarifies wine, beer, and juice samples ahead of HPLC testing for organic acids, sugars, and preservatives.
- Compressed Gas Filtration - Passes nitrogen and other inert gases freely while holding back moisture, protecting instruments and gas lines.
- Culture Vessel Filling - Equalizes pressure in sealed culture vessels by venting displaced air, keeping fill and drain lines fully closed.
- Bioreactor Vent Protection - Repels water while venting bioreactors and fermenters, keeping process air and gases moving freely through the line.