Tisch Scientific PVDF Syringe Filters, 0.45 µm, 25 mm, 100/Pk - SF18310
Tisch Scientific's sales team brings fast, courteous service to every filtration order, from first quote through fulfillment. Many syringe filters ship with lot-specific quality documentation, giving analysts documented traceability beyond what an ad hoc bulk filtration setup typically provides. PVDF holds up to alcohols and mild hydrocarbon solvents while enforcing absolute cutoff at its micron rating and repels water for dependable gas and vent filtration. The polypropylene housing presses snugly against the membrane during the pass while keeping sample purity intact through the filtration pass and is supplied pre-sterilized in individual packaging for sterile sample preparation. For routine sample preparation across many methods, each analytical run starts with a consistent, particle-free sample without added hardware or a cleaning step.
Prefiltration
- Nominal depth rating sized for coarse particulate capture
- Two-stage construction with the prefilter ahead of the final membrane
- High dirt-holding capacity for the heaviest particulate loads
- Media graded from coarse to fine across the stack
Membrane Characteristics
- Resistance to hydrolytic degradation exceeds that of nylon membranes
- Hydrophobic surface chemistry gives PVDF a water contact angle above 100 degrees, blocking wetting
- Organic solvent resistance beats PES or nylon at comparable pore size
- Fluorinated polymer chemistry resists ozone, UV, and ionizing radiation
- Mechanically durable membrane holds integrity under filtration pressure
Housing Characteristics
- Inert polyolefin wall contributes minimal sample adsorption to the filtrate
- Medical-grade polypropylene with broad chemical compatibility
- Rigid polypropylene body maintains its geometry through routine filtration pressure
- Standardized luer connection geometry provides secure engagement with standard syringe tips
Particulates left in your organic solvents and reagents carry downstream into the step that depends on a clean feed. Reliable solvent prefiltration keeps a stray particulate from carrying into your downstream work so your downstream method starts with a clean sample. Standardize your filtration purchases across every method with volume pricing and documentation from the Tisch Scientific team.
Sterilization Guidance
Factory sterilization supports immediate use in workflows where sterility assurance matters.
For more information about chemical compatibility, please review our Chemical Compatibility Chart.
- Bubble Point (psi)
- 5.8psi
- Connection Type
- Luer-Lok/Luer Slip
- Diameter
- 25mm
- Filtration Area
- 4.08cm²
- Flow Rate
- 32ml
- Holdup Volume
- 100μL
- Material
- Polyvinylidene Fluoride (PVDF)
- Maximum Operating Pressure
- 87psi
- Maximum Operating Temperature (°C)
- 60°C
- Membrane Thickness (µm)
- 100-130μm
- Pack Count
- 100
- Pore Size (µm)
- 0.45
- Prefilter (Yes/No)
- Yes
- Prefilter Material
- GF+GF+PP
- Sterility
- Sterile
- Volume Throughput (ml)
- 50ml
- Weight
- 0.88
- Wettability
- Hydrophobic
- Bioreactor Vent Protection - Repels water while venting bioreactors and fermenters, keeping process air and gases moving freely through the line.
- Dissolution Testing - Removes undissolved particles from timed USP 711 dissolution aliquots, preventing skewed potency and release results.
- Beverage QC - Clarifies wine, beer, and juice samples ahead of HPLC testing for organic acids, sugars, and preservatives.
- Petroleum Sample Prep - Removes particulates from fuel and lubricant samples ahead of viscosity and quality-control testing.
- Vial and Tubing Venting - Blocks liquid while venting sealed vials and tubing lines, keeping pressure equalized during fluid transfer steps.
- Culture Vessel Filling - Equalizes pressure in sealed culture vessels by venting displaced air, keeping fill and drain lines fully closed.